PAC Universal Analog/CAN-Bus Steering Wheel Control Interface With DIP Switch Programming SWI-RC
SWI-RC
Speed through your radio replacement installation when using the SWI-RC-1 to retain your factory steering wheel controls.
To program the SWI-RC-1:
Go to the SWI-RC-1 installation guide from your PC, MAC, or mobile device
Select the make/model/year and what of brand radio you are installing
Set the DIP switches according to the information provided.
In addition to DIP switch programming, the SWI-RC-1 can be manually programmed like the Classic SWI-RC. You will also save time using the accessory output generated by the SWI-RC-1 in CAN-Bus/LAN/Class II vehicles instead of searching for an accessory wire for your aftermarket radio.
Important Note: On some vehicles, you may need a voltmeter to locate the correct wires to connect to the SWI-RC. If you have no car audio installation experience, you should consider professional installation. The SWI-RC works with most Alpine, Clarion, Dual, Jensen, JVC, Kenwood, Pioneer, and Sony stereos that have a wired remote control input port or a dedicated steering wheel input, but please call or email us to confirm compatibility with your radio.
Wiring Advisory: You'll usually have to tap into one to three wires in your vehicle at the radio location to connect this interface. If you're using a PAC OEM integration adapter to connect your new car stereo to your vehicle, then it most likely will have a prewired connector for this PAC steering wheel audio control adapter. In these cases, no additional wiring in required. PAC does provide custom wiring instructions for all confirmed compatible vehicles on their website.
What's in the box:
Steering wheel control interface module (with attached 9" blue/yellow wire and 34" cable terminated by a right-angle male 3.5mm connector)
24" Wiring harness
Packet of 8 resistors (includes 47 ohms/100 ohms/150 ohms/560 ohms/1000 ohms/1500 ohms/3900 ohms/5100 ohms)
0.47uF Capacitor
Installation Instructions
2 Vehicle Connector Charts
Bluetooth Commands note
Technical Support contact information
Warranty: 1 year Manufacturer
Suncoast Marine and Auto is a Trusted Authorized Dealer
California: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
SWI-RC
Speed through your radio replacement installation when using the SWI-RC-1 to retain your factory steering wheel controls.
To program the SWI-RC-1:
Go to the SWI-RC-1 installation guide from your PC, MAC, or mobile device
Select the make/model/year and what of brand radio you are installing
Set the DIP switches according to the information provided.
In addition to DIP switch programming, the SWI-RC-1 can be manually programmed like the Classic SWI-RC. You will also save time using the accessory output generated by the SWI-RC-1 in CAN-Bus/LAN/Class II vehicles instead of searching for an accessory wire for your aftermarket radio.
Important Note: On some vehicles, you may need a voltmeter to locate the correct wires to connect to the SWI-RC. If you have no car audio installation experience, you should consider professional installation. The SWI-RC works with most Alpine, Clarion, Dual, Jensen, JVC, Kenwood, Pioneer, and Sony stereos that have a wired remote control input port or a dedicated steering wheel input, but please call or email us to confirm compatibility with your radio.
Wiring Advisory: You'll usually have to tap into one to three wires in your vehicle at the radio location to connect this interface. If you're using a PAC OEM integration adapter to connect your new car stereo to your vehicle, then it most likely will have a prewired connector for this PAC steering wheel audio control adapter. In these cases, no additional wiring in required. PAC does provide custom wiring instructions for all confirmed compatible vehicles on their website.
What's in the box:
Steering wheel control interface module (with attached 9" blue/yellow wire and 34" cable terminated by a right-angle male 3.5mm connector)
24" Wiring harness
Packet of 8 resistors (includes 47 ohms/100 ohms/150 ohms/560 ohms/1000 ohms/1500 ohms/3900 ohms/5100 ohms)
0.47uF Capacitor
Installation Instructions
2 Vehicle Connector Charts
Bluetooth Commands note
Technical Support contact information
Warranty: 1 year Manufacturer
Suncoast Marine and Auto is a Trusted Authorized Dealer
California: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
SWI-RC
Speed through your radio replacement installation when using the SWI-RC-1 to retain your factory steering wheel controls.
To program the SWI-RC-1:
Go to the SWI-RC-1 installation guide from your PC, MAC, or mobile device
Select the make/model/year and what of brand radio you are installing
Set the DIP switches according to the information provided.
In addition to DIP switch programming, the SWI-RC-1 can be manually programmed like the Classic SWI-RC. You will also save time using the accessory output generated by the SWI-RC-1 in CAN-Bus/LAN/Class II vehicles instead of searching for an accessory wire for your aftermarket radio.
Important Note: On some vehicles, you may need a voltmeter to locate the correct wires to connect to the SWI-RC. If you have no car audio installation experience, you should consider professional installation. The SWI-RC works with most Alpine, Clarion, Dual, Jensen, JVC, Kenwood, Pioneer, and Sony stereos that have a wired remote control input port or a dedicated steering wheel input, but please call or email us to confirm compatibility with your radio.
Wiring Advisory: You'll usually have to tap into one to three wires in your vehicle at the radio location to connect this interface. If you're using a PAC OEM integration adapter to connect your new car stereo to your vehicle, then it most likely will have a prewired connector for this PAC steering wheel audio control adapter. In these cases, no additional wiring in required. PAC does provide custom wiring instructions for all confirmed compatible vehicles on their website.
What's in the box:
Steering wheel control interface module (with attached 9" blue/yellow wire and 34" cable terminated by a right-angle male 3.5mm connector)
24" Wiring harness
Packet of 8 resistors (includes 47 ohms/100 ohms/150 ohms/560 ohms/1000 ohms/1500 ohms/3900 ohms/5100 ohms)
0.47uF Capacitor
Installation Instructions
2 Vehicle Connector Charts
Bluetooth Commands note
Technical Support contact information
Warranty: 1 year Manufacturer
Suncoast Marine and Auto is a Trusted Authorized Dealer
California: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
